The following information is provided by the container supply Henan peace? Rubber? Plastic container? Henan Green 10 cubic PE tank 10 tons of plastic water tank tower towers high Product / Service Description Ping 10 cubic PE tank 10 tons of plastic water tank tower high large plastic water tanks and more for rotational molding production, a molding. Such as plastic water tanks, plastic jar, PE plus kits, plastic tanks, plastic drums, fish and other large square box of plastic products, product thickness of large, high-durability, product size is relatively large. Production is relatively time-consuming. Huge individuals. Performance: forming a smooth inside and outside, with good hygiene and UV resistance, impact resistance, anti-earthquake, not aging, not long algae, easy to wash, rodent, termite, install and easy to move. General resistance to acid type water tank can hold hot liquids, chemicals, strong acid liquid. Generally resistant to high temperature of 90 degrees, the minimum can withstand low temperatures of minus 30 degrees. After adding the recipe to a high temperature above 114 degrees. Foreign abbreviated as polyethylene PE, low density polyethylene maximum application temperature is 60 ℃, high-density polyethylene 70 ℃. Minimum application temperature of -70 ℃. With no welding seams, no leakage, non-toxic, anti-aging, shock, corrosion resistance, long life, health standards and so on. Tanks are generally equipped with a remote level HYFI electric valve, HYJK type water level monitoring system and HYQX-II tank automatic cleaning system and HYZZ-2-A-type self-cleaning disinfection tank, tank overflow pipe and tank drain valve after Connect and set up insect nets, water level should be two different snorkel (set Insect), located both inside and outside the tank ladder; tanks generally have inlet, outlet pipe (live outlet, fire outlet), overflow pipe, drainage pipes, tanks divided according to different functions of living water tank, fire water tanks, production tanks, air defense tanks, chemical storage tanks six kinds of household water tower, the strict sense of the toilet flush tank and tank car tank does not belong to the scope. Technical requirements a safe container, water tanks shall comply with the requirements of this standard, manufactured in accordance with drawings and dimensions specified. 2, after the completion of each tank welding without loosening fasteners, each solder connections may not tainted, not tainted pieces phenomenon. 3, the tank must be full weld, welding tank outer surface to be smooth, beautiful, no slag, weld-free, no holes, no cracks, weld and can not have a concave crack, separation, not a cut hand phenomenon. Water tank welds need to be polished. At the same time should meet the requirements of welding requirements in Table 2 below. 4, flat bottom tank should remain flat, the degree of deformation to meet the requirements of Table 3. 5, the top of the tanks and manholes must be fully welded, with quality requirements in 4.3. 6, water tank connector must be good weldability, while trying to maintain the vertical, at least no more than the inclination of 1 °. 7, the insulation layer and the outer tank with a solid, smooth appearance. Better insulation using polyurethane foam plastic insulation material or performance; outer decorative shell with stainless steel or other suitable material, the surface shall be uneven, there are scratch marks or rust, to the requirements of Table 2. 8, tolerances for dimensions shall meet the requirements of Table 3. 9, PE water tank filled with water, without infiltration, water leakage, there should be no significant deformation phenomenon, according to the welded steel pressure vessel filled with water experiments related terms. (GB50242-2002 Building Water and Heating Engineering Construction Quality Acceptance of regulation range of 10, should be erected perpendicular PE tank, verticality should meet the requirements of Table 3. 11, the actual installation of water tanks PE should not be less than the nominal volume 12, PE water tank used in stainless steel shall conform to GB / T3280's water tank used for the plate to be made of 304 stainless steel inside and outside the plate thickness tolerances of less than 10%. 13, PE water tank used for carbon steel shall comply with GB / T 700 for water tank All iron parts must be embalmed, required twice a rust rust treatment, the exposed part of the need to brush twice silver paint. 14, inside and outside the protruding parts PE tank should be done into the hole flanging process or do other protective treatment avoid cuts people. 15, after the clean water tank filled with water in line with the provisions of GB5749, standing 1h, at the outlet of the water tank shall comply with the requirements of GB5752 plastic tanks including plastic towers, plastic containers, plastic drums, plastic square boxes and other large plastic containers, plastic water tank with a new dedicated mainly to the high concentration of raw materials rotomolding polyethylene (HDPE) is made of HDPE materials are generally environmentally friendly, acid and alkali, high and low temperature properties of. HDPE made of plastic You can reach food grade tank. PE PE plastic tanks imported raw materials, the international advanced level ROTATION (rotational molding) technology, combined with the needs of users, strict quality control in one to produce varieties of specifications, modeling beautiful water storage tank. and to undertake all kinds of strange Shaped the rotomolding products production research and development, a variety of rotational molding machines, hot-box machine, mold development and research, and provide external technical services produced by a variety of plastic products modeling nice, non-toxic , tasteless, acid and alkali resistance, impact resistance, high temperature, cold and difficult to aging, easy installation and transportation, is widely used in the construction of water, water, medicine, food, electronics, chemicals, aquaculture, textile and other industries. Plastic storage cans of pure polyethylene (LLDPE LLDPE, high density polyethylene HDPE) as raw material, the use of special rotational molding process as a whole. with no welding, no leakage, non-toxic, light weight, anti-aging, shock, corrosion resistance, long life and other advantages. integrally molded integrity, corrosion resistance, long life advantages particularly prominent. The reaction can be stored and the vast majority of inorganic acids, alkalis, salt solutions and most organic solvents, can partially replace stainless steel titanium, nickel High alloy steel and other materials, products, storage and transportation of dangerous goods in line with regulations, is to store chemical corrosion reaction solution, clean solution ideal storage container This product complies with national health standards, alternative food-grade stainless steel container shipping solution Product material: high quality imports of raw materials and food-grade plastic material product formulation process: the use of foreign mature ROTATIONAL (rotational molding) technology, process integrity, a molding supply jar, high degree of sintering, fine density, high strength, high temperature, easy to use. and easy to carry, light weight also wrestling is not bad, combined with modern high-tech products, much to replace the earthen jar, product launch, performance and benefits to attract all kinds of large distillery products: products with no welding seamless, Non-toxic, tasteless, acid resistance, impact resistance, high temperature (80 ℃), anti-freeze (-49 ℃), does not leak, not aging, no maintenance and cleaning, installation and transportation